top of page

  DZ-76   Σετ εξολκέα ταχείας βίδας με λαβή

Extractor bit set for stripped and broken screws !
  • Μύτες εξαγωγής τύπου Press & Twist για βίδες Philips #0, #1 & #2 και Strike &
    Μύτες εξολκέα τύπου περιστροφής για τις βίδες #2 της Philips

  • Έρχεται με εργονομική λαβή λαβής με εξάγωνο 13mm. μαξιλάρα

  • Μέγεθος bit: 105mm x Hex. 6,35 χλστ

  • Υλικό μύτης: χάλυβας υψηλής περιεκτικότητας σε άνθρακα

BUY NOW.jpg
GB.jpg
amazon.jpg
DE.jpg
amazon.jpg
JP.jpg
amazon.jpg
Video
Video
Features
Features

Ordinary Screwdriver

Rapid Screw Extractor

Features.png
For-countersunk-screws.png
For-countersunk-screws.png
How to use
Press & Twist
Strike & Turn

Press & Twist type  (for slightly damaged screws) 

1) Insert the bit into the handle grip.

2) Place the bit tip into the screw head, then scrape away
     burs in the recess by twisting it back and forth lightly.  
     *Do not attempt to hit the bit with a hammer.

3) After you feel the bit tip catches the corner of recess, 
     give a jerk counterclockwise while pressing firmly 
     downward.

Strike & Turn type  (for heavily damaged screws)

1) Clean out any steel chips left in the screw recess.

2) Fix the rubber sleeve to the Strike & Turn bit and position 
     the tip in the recess.

3) Strike the end of the bit with a hammer to stick the tip 
     into the recess.

4) Make sure the bit is self-standing upright, and then affix 
     the grip onto the bit. 
     *Do not hit the grip with a hammer.

5) Give a jerk counterclockwise while pressing firmly

     downward.

Related products
Related
Rapid Screw Extractor for Phillips  (DBZ-51/57/58)
Screw Extractor for Hex. Socket  (DBZ-53/54/56)
Rapid Screw Extractor Handle Grip with DBZ-51/52 bits (DBZ-60G)

Rapid Screw Extractor
Handle Grip with DBZ-51/52 bits
(DBZ-60G)

High-torque Handle Grip for DBZ series  (DBZ-50B) 100mm in width

High-torque Handle Grip for DBZ series

(DBZ-50B)
100mm in width

Go-through Driver Handle ø38 x 121(L) mm with 13mm Hex Bolster (DZ-70)

Cross Section

Go-through Driver Handle ø38 x 121(L) mm
with 13mm Hex Bolster
(DZ-70)

Go-through Driver Handle ø38 x 121(L) mm  with 13mm Hex Bolster and DBZ-51 Extractor Bit (DZ-71)

Go-through Driver Handle ø38 x 121(L) mm 
with 13mm Hex Bolster and DBZ-51 Extractor Bit
(DZ-71)

Υποδοχή μπιτ επέκτασης DR-22, DR-23, DR-24

DR-22     100mm

DR-23     150mm

DR-24     190mm

* DBZ-51~65 Extractors attachable
* The bit holder can be used with an Impact Driver, too.

Hex. 6.35.jpg

DR-25     99mm

* DBZ-51~65 Extractors and DR-22~24 attachable
* Slide the sleeve forward to swing the tip to 15 degrees max.
* Can be used with an Impact Driver only in the straight mode.

Specs
Specifications
bottom of page